[Techtoolslist] leland off road pal dump needed u85

[Fabrizio Vasile]

I use this device to dump protected PLDs (in the project archive there 
is also the software needed to analyze binary dumps):

http://dreamjam.co.uk/emuviews/pal/index.html




Il 17/03/2015 17:29, John Robertson ha scritto:
> What is the hardware needed? Perhaps it can be duplicated on this side 
> of the pond...
>
> John :-#)#
>
> On 03/17/2015 9:02 AM, Fabrizio Vasile wrote:
>> Yes, I have the hardware to dump it.The problem I'm located in Italy 
>> and there are chances the chip could get lost during shipping.
>>
>> Il 17/03/2015 16:51, William Stillwell ha scritto:
>>> It would be nice to get the chip / jed to Fabrizzo to put up on 
>>> jammarcade
>>> pld archive.
>>>
>>> He already mentioned he has the hardware to dump them.
>>>
>>>
>>>
>>> -----Original Message-----
>>> From: Techtoolslist [mailto:techtoolslist-bounces at flippers.com] On 
>>> Behalf Of
>>> Gary M. McTaggart
>>> Sent: Tuesday, March 17, 2015 10:11 AM
>>> To: Technical Tools Mail List
>>> Subject: Re: [Techtoolslist] leland off road pal dump needed u85
>>>
>>> I'll forward to Aaron Giles and see if he has the correct stuff to dump
>>> these too. I could bring the chip to him.
>>>
>>>> On Mar 17, 2015, at 7:08 AM, Gary M. McTaggart 
>>>> <gary.mctaggart at gmail.com>
>>> wrote:
>>>> If you have your adapter, I can get a chip to you for the track pack
>>>> Clay. I was in Portland yesterday. Wish I would had known then. :)
>>>>
>>>> I can mail you the chip for the track pack.
>>>>
>>>> Otherwise I can use my rom burner to read it, but that may take 
>>>> longer for
>>> me to get to.
>>>>
>>>>
>>>>> On Mar 17, 2015, at 12:32 AM, Clay Cowgill <c.cowgill at comcast.net> 
>>>>> wrote:
>>>>>
>>>>> I might still have the exact adapter.  I'll look for it Tuesday and
>>>>> report back here... I can take a few pictures of it. (I might even
>>>>> have a Track Pack boardset and could just read the PROM in here. I
>>>>> don't remember what's our machine in storage. I'll look. If nothing
>>>>> else, if our PCB is the original one just reading and duplicating
>>>>> that would serve as a proof of
>>>>> concept.)
>>>>>
>>>>> OE&CE can just be disconnected. Looking at the schematics all the
>>>>> outputs are going to be push/pull (no tristate), so nothing 'special'
>>>>> required to brute-force the dump.  (Also, two outputs are not even
>>>>> used.)
>>>>>
>>>>> -Clay
>>>>>
>>>>> -----Original Message-----
>>>>> From: Techtoolslist [mailto:techtoolslist-bounces at flippers.com] On
>>>>> Behalf Of tonyhtbsusa
>>>>> Sent: Monday, March 16, 2015 6:17 PM
>>>>> To: 'Technical Tools Mail List'
>>>>> Subject: Re: [Techtoolslist] leland off road pal dump needed u85
>>>>>
>>>>> Do you have a pinout of how you did it Did you go from pin one to pin
>>>>> one Did it matter what address line or data line went to what pin on
>>>>> eprom The
>>>>> 2716 starts at address 7 on pin 1 And data lines are split From side
>>>>> to side What did you do with /oe or /ce Thanks tony
>>
>
>


---
Questa e-mail è stata controllata per individuare virus con Avast antivirus.
http://www.avast.com